Our Basement Part 33: Installing Vinyl Faux Slate Flooring & Whitewash

March 19, 2012 — 8 Comments

 

Faux Slate Floor w/ Space for Grout

It was a long slog this weekend in the basement (especially with such lovely weather outside). I am now the queen of faux slate flooring. We ran into some issues with the floor, so I didn’t get quite as far as I would have liked. The good news is that the floor is down (at least in the bathroom). The bad news is that I still need to grout (that is for tonight). Mr. S. also got most of the whitewashing done in the main space.

Installing the “Luxury” Vinyl Tile:
(TrafficMaster Ceramica Resilient Vinyl in Coastal Gray @ Home Depot)

Staggered 12x12 Tile Layout

Step 1: Sketch out a rough layout on paper. In my case I used AutoCAD. The tiles are listed as being 12×12, but in actuality they are 11 3/4 x 11 3/4 (to allow for a 1/4 grout joint). We decided to go with a staggered pattern, which I think helps make it look more modern. I also used this when estimating how much to order.

Step 2: Acclimate the tile (ours have been sitting in the basement for the last month). If I had this to do over again I would have pulled the tiles out of the boxes and had them sit out where it was a little warmer.

Floor after Leveling

Step 3: Prep the floor. This includes leveling (our contractor used a self leveling product and ground down the high spots with an old school stone). Once the floor was level we used a floor prep product for concrete flooring (recommended by the manufacturer). This makes the floor slightly sticky and ideal for making the tile stick (or at least it is suppose to).

Getting Started with the Layout

Step 4: Do a rough layout with the actual tiles. I also doubled checked my original sketch. Of course the walls were off by about an inch, so I adjusted accordingly. I also wanted to make sure that we ended at a full tile where the laundry area meets the main space, so I carefully measured back from there. That left me with a row of 8 1/4″ tiles on the back wall. We were lucky that all of the walls were perpendicular (I checked and rechecked) so I could cut the tiles all the same depth for the back wall and work out from there.

Tools that I used: a good Utility Knife w/ LOTS of blades, Needle Nose Vise Grips, Pencil & Square

Step 5: Cutting the tile! The tile is nice and thin and cuts quite easily (yeah!). For the straight cuts you just score it with the utility knife a few times and then you can snap it with your hands. For more complex cuts I scored the shape and carefully pulled down with the need nose vise grips right next to the cut (on the bad side). This worked quite well, although sometimes took several turns to get all of the unused portion off. One of the keys to a good cut is a sharp blade! So, remember to change them frequently!

Step 6: Installing the tile! I had 1/8 spacers on hand from the shower so I put two together to get the 1/4″ spacing that I needed. After getting the tile lined up I carefully removed the backing of the tile and placed it down. I then double checked the spacing on all sides, then pushed it down into place. Then I stepped on it and used a rolling pin at the joints. Easy right? Well, okay this is where things started to go badly! Quickly I noticed that the tiles weren’t sticking as well as I would have liked. So then I started warming the tiles up by holding them up to the heater in the ceiling, hoping that would help. It did help but I was still noticing than some of them were not adhering as well as I would like!

Vinyl Tile Adhesive

Luxury Vinyl Tile Adhesive

Step 6A (Plan B): I ran to the store and picked up vinyl adhesive (which I have used before). According to my tile’s warranty I have now voided it! I had read the reviews of the tile and more than one person had used the vinyl adhesive without problem (to ensure good adhesion). So I pulled up all of the loose tile and troweled on the adhesive.

*Of course now I realize that there is a special adhesive for “Luxury” vinyl tile. Oops, I guess I used the wrong one (I don’t think I saw two options in the store).

Step 7: Wait for the adhesive to become tacky (this took about an hour).

Step 8: Apply the tiles.

Jamb Saw

Step 9: Cutting around door trim. So while I was picking up the adhesive I had also realized that the door trim went all the way to the floor, so I couldn’t get the tile underneath. I have seen contractors undercut the jamb before, but I have never done it, but it means I much more professional look so I though I should try and do this.  I was pleased to find this Irwin Jamb Saw for $10.98.  And it worked just as promised. Yeah! I just placed a scrap tile at the location and cut against the jamb.

Step 10: Wait for the adhesive to dry!

Step 11: Install the Faux Grout: Stay tuned!

Close Up of Ceramica Tile. Cut edge on left and Finished edge on right. The finished edge curves down slightly.

* To see all of the posts about our basement click here.

8 Comments

8 responses to Our Basement Part 33: Installing Vinyl Faux Slate Flooring & Whitewash

  1. So happy to have found your blog. I have been lookong for rectangular “slate” vinyl. I had only tried Lowes however and no dice. I think rectangular is not as common and makes the vinyl look almost like slate.or ceramic. We are starting kitchen reno.next week and would love this floor for kitchen and eat in. I’m a little concerned abt the grout holding up. Can’t wait to see your progress.

  2. Hi Sarah! Welcome! They also make this in a 12×24 if you prefer rectangles. These are 12×12 (although they look rectangular in the photos). This color (Coastal gray) is special order, it took about a week and a half to come in. You can special order it at the store or from the website.

  3. You mentioned in a previouse post that you were going to use Barricade subfloor tiles. Did you end up doing this?

    I am having a hard time deciding between Barricade and Dricore under the tiled basement floor.

    I would love to know your thoughts.

  4. Hi Anna (and welcome)!

    We ended up not putting down anything because our ceiling is so low (I wish we could have put something like that down to separate the finished floor from the concrete). I like the Barricade product, because it provide insulation (and if you are going to the trouble of putting something like this in it seems like you should add some thermal separation). I don’t like that both of these products use OSB for the top rather than plywood (this will tend to deteriorate if wet, while plywood will hold up to some moisture). Another option is to create your own separation. You can use 1″ XPS (extruded polystyrene) and install 1/2″ plywood on top. This should be less expensive than Barricade, although it more difficult to work with. Here is a useful link on basement insulation:

    http://www.buildingscience.com/search?SearchableText=basement (select RR-0309)

    Also here is a link for how to install the barricade:
    http://www.wikihow.com/Install-an-Insulated-Barricade-Modular-Panel-System-in-Basements

  5. I fell into your blog because I was googling cutting these ceramica tiles. I want to make a pattern that requires rectangular shaped tiles, but the 12x24s are too big for my small room. I was wondering, based on your experience, do you think if I were to cut the 12x12s into 12x6s, that they would LOOK like they were cut in half? Sorry if thats confusing. I just don’t know if theres some sort of curve to the edges so that the side we cut would not match the other 3 sides or if there would be some sort of noticeable change in the pattern.

    • Jessie,

      Ceramica does have a little bit of a curve on the sides (probably so it can take the grout better). I found that the cut lines never look as good as the finished side. In my case there were a couple of joints that ended up with the cut edge exposed. If you look closely you can tell. I cut mine with a utility knife, I wonder if you might get a slightly better edge with another tool. I feel that part of the problem is that unlike say a vinyl composite tile which has the same material all the way through the finish on these is only on the surface, but on the finished sides they have continued that finish around the side. I just added a picture at the bottom of the post to show you what it looks like. I think you might be disappointed with the cut edges. I know when I was looking I would have loved to have found a 6×12 or 8×12 vinyl tile.

      P.S. I see you are from Pittsburgh. I went to college there and have a soft spot for the place!

  6. Was wondering if you happy with the cermica? Just discovered this product & found you through my Google search.
    Thanks! Erin
    I’m from Pittsburgh too! Not currently living there, though.

    • Hi Erin,

      Yes we are happy with the cermica. It is holding up well and it doesn’t show dirt (which is really nice for our basement area).

Leave a Reply to Erin Cancel reply

Text formatting is available via select HTML. <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

*